Chargement...
 
[Voir/Cacher menus de gauche]
[Voir/Cacher menus de droite]

7 - Autres sujets : le nimp'

> Forums de discussion > 7 - Autres sujets : le nimp' > [RESOLU] librazik et la wifi (puce rt73)
Dernier post
Page : 1/3   -   Aller directement à la page : 1  2  3 

[RESOLU] librazik et la wifi (puce rt73)

calixtus06 utilisateur non connecté
Hello

J'ai installé librazik sur mon nouvel ordi en suivant le guide du site de librazic. La wifi fonctionne pour l'installation. Une fois la clef usb enlevé je redémarre. On me redemande de choisir la box , de réinscrire la clef de sécurité et là ça cherche pendant des plombes sans valider la connection ( ???) .

" obtention d'une adresse réseau wi-fi pour "freebox_nicolas_ni"....

Des idées ?

Merci d'avance

Nico

sub26nico utilisateur non connecté France
Quel ordi? carte wifi?

zebassprophet utilisateur non connecté
c'est un probleme que j'ai eu
faut regarder du coté de Debian
me semble qu'il faut installer les drivers non libre pour ta clef

essaye deja de faire lsusb en ligne de commande et de donner la reference de ton chipset

good luck

tenryu utilisateur non connecté France
Je plussoie sur ce que dit ZBP. Normalement, lors du boot, tu devrais avoir un message qui te parle de microcode qui manque et qu'il faudrait charger.

calixtus06 utilisateur non connecté
sub26nico écrit :
Quel ordi? carte wifi?


root@LibraZiK-studio-audio:/home/nicolasmao2# ifconfig
enp0s25   Link encap:Ethernet  HWaddr 18:03:73:dc:f6:7c  
          inet adr:192.168.0.33  Bcast:192.168.0.255  Masque:255.255.255.0
          adr inet6: fe80::1a03:73ff:fedc:f67c/64 Scope:Lien
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:3641 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2383 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:1000 
          RX bytes:3824777 (3.6 MiB)  TX bytes:279149 (272.6 KiB)
          Interruption:20 Mémoire:e1a00000-e1a20000 

lo        Link encap:Boucle locale  
          inet adr:127.0.0.1  Masque:255.0.0.0
          adr inet6: ::1/128 Scope:Hôte
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:25 errors:0 dropped:0 overruns:0 frame:0
          TX packets:25 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:1 
          RX bytes:3154 (3.0 KiB)  TX bytes:3154 (3.0 KiB)

wlx0008d3359008 Link encap:Ethernet  HWaddr 00:08:d3:35:90:08  
          adr inet6: fe80::208:d3ff:fe35:9008/64 Scope:Lien
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:18 errors:0 dropped:0 overruns:0 frame:0
          TX packets:30 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:1000 
          RX bytes:5348 (5.2 KiB)  TX bytes:6199 (6.0 KiB)

root@LibraZiK-studio-audio:/home/nicolasmao2#


root@LibraZiK-studio-audio:/home/nicolasmao2# lscpu
Architecture :        x86_64
Mode(s) opératoire(s) des processeurs : 32-bit, 64-bit
Boutisme :            Little Endian
Processeur(s) :       4
Liste de processeur(s) en ligne : 0-3
Thread(s) par cœur : 1
Cœur(s) par socket : 4
Socket(s) :           1
Nœud(s) NUMA :       1
Identifiant constructeur : GenuineIntel
Famille de processeur : 6
Modèle :             42
Nom de modèle :      Intel(R) Core(TM) i5-2400 CPU @ 3.10GHz
Révision :           7
Vitesse du processeur en MHz : 2938.604
Vitesse maximale du processeur en MHz : 3400,0000
Vitesse minimale du processeur en MHz : 1600,0000
BogoMIPS :            6186.75
Virtualisation :      VT-x
Cache L1d :           32K
Cache L1i :           32K
Cache L2 :            256K
Cache L3 :            6144K
Nœud NUMA 0 de processeur(s) : 0-3
root@LibraZiK-studio-audio:/home/nicolasmao2#


root@LibraZiK-studio-audio:/home/nicolasmao2# lsusb
Bus 002 Device 004: ID 046d:c03e Logitech, Inc. Premium Optical Wheel Mouse (M-BT58)
Bus 002 Device 003: ID 0603:00f2 Novatek Microelectronics Corp. 
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 06f8:e010 Guillemot Corp. HWGUSB2-54-LB
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@LibraZiK-studio-audio:/home/nicolasmao2#



ça répond à la question ?

sub26nico utilisateur non connecté France
je suppose, mais j'arrive pas à avoir le modèle de la carte wifi,
à qui il faut trouver les drivers.
Dans Synaptic, actives les dépots non-free et contrib puis fais
une recherche avec "wifi". C'est mieux si tu connais le nom des paquets
recherchés, sinon tu installes tout ce qui concerne les drivers wifi.
C'est un peu (beaucoup?) bourrin, mais ça a marché pour moi.
Vérifies aussi que les modules ne soit pas blacklistés.

calixtus06 utilisateur non connecté
HWGUSB2-54-LB
par contre le driver ?

C'est bien la première fois que ça m'arrive d'autant qu'elle marchait pendant l'install (???)

calixtus06 utilisateur non connecté
Image

Image

Image

Quoi comprendre ?

calixtus06 utilisateur non connecté
zebraprophet écrit :
essaye deja de faire lsusb en ligne de commande et de donner la reference de ton chipset


Image

calixtus06 utilisateur non connecté
tenryu écrit :
Je plussoie sur ce que dit ZBP. Normalement, lors du boot, tu devrais avoir un message qui te parle de microcode qui manque et qu'il faudrait charger.


[    0.361437] pci 0000:00:1d.0: reg 0x10: [mem 0xe1a50000-0xe1a503ff]
[    0.361515] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.361568] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.361602] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[    0.361678] pci 0000:00:1e.0: System wakeup disabled by ACPI
[    0.361712] pci 0000:00:1f.0: [8086:1c4c] type 00 class 0x060100
[    0.361868] pci 0000:00:1f.2: [8086:1c02] type 00 class 0x010601
[    0.361881] pci 0000:00:1f.2: reg 0x10: [io  0x30d0-0x30d7]
[    0.361888] pci 0000:00:1f.2: reg 0x14: [io  0x30c0-0x30c3]
[    0.361894] pci 0000:00:1f.2: reg 0x18: [io  0x30b0-0x30b7]
[    0.361901] pci 0000:00:1f.2: reg 0x1c: [io  0x30a0-0x30a3]
[    0.361908] pci 0000:00:1f.2: reg 0x20: [io  0x3060-0x307f]
[    0.361915] pci 0000:00:1f.2: reg 0x24: [mem 0xe1a40000-0xe1a407ff]
[    0.361951] pci 0000:00:1f.2: PME# supported from D3hot
[    0.362014] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
[    0.362027] pci 0000:00:1f.3: reg 0x10: [mem 0xe1a30000-0xe1a300ff 64bit]
[    0.362046] pci 0000:00:1f.3: reg 0x20: [io  0x3040-0x305f]
[    0.362186] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.362265] pci 0000:00:1c.2: PCI bridge to [bus 02]
[    0.362270] pci 0000:00:1c.2:   bridge window [io  0x2000-0x2fff]
[    0.362274] pci 0000:00:1c.2:   bridge window [mem 0xe1000000-0xe19fffff]
[    0.362282] pci 0000:00:1c.2:   bridge window [mem 0xe0000000-0xe09fffff 64bit pref]
[    0.362344] pci 0000:00:1e.0: PCI bridge to [bus 03] (subtractive decode)
[    0.362352] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7 window] (subtractive decode)
[    0.362353] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff window] (subtractive decode)
[    0.362354] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[    0.362355] pci 0000:00:1e.0:   bridge window [mem 0xcfa00000-0xfeafffff window] (subtractive decode)
[    0.362356] pci 0000:00:1e.0:   bridge window [mem 0xfed40000-0xfed44fff window] (subtractive decode)
[    0.362777] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.362819] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.362860] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.362900] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[    0.362940] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 *5 6 7 10 12 14 15)
[    0.362980] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[    0.363020] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 *3 4 5 6 7 10 12 14 15)
[    0.363060] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[    0.363120] ACPI: Enabled 2 GPEs in block 00 to 3F
[    0.363236] vgaarb: setting as boot device: PCI:0000:00:02.0
[    0.363237] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.363238] vgaarb: loaded
[    0.363239] vgaarb: bridge control possible 0000:00:02.0
[    0.363294] PCI: Using ACPI for IRQ routing
[    0.364716] PCI: pci_cache_line_size set to 64 bytes
[    0.364748] e820: reserve RAM buffer [mem 0x0009ac00-0x0009ffff]
[    0.364749] e820: reserve RAM buffer [mem 0xca9fa000-0xcbffffff]
[    0.364750] e820: reserve RAM buffer [mem 0xcadb7000-0xcbffffff]
[    0.364751] e820: reserve RAM buffer [mem 0xcb000000-0xcbffffff]
[    0.364752] e820: reserve RAM buffer [mem 0x12e000000-0x12fffffff]
[    0.364875] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    0.364879] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[    0.366898] clocksource: Switched to clocksource hpet
[    0.371888] VFS: Disk quotas dquot_6.6.0
[    0.371918] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.371990] pnp: PnP ACPI init
[    0.372117] system 00:00: [io  0x0680-0x069f] has been reserved
[    0.372118] system 00:00: [io  0xffff] has been reserved
[    0.372119] system 00:00: [io  0xffff] has been reserved
[    0.372121] system 00:00: [io  0xffff] has been reserved
[    0.372122] system 00:00: [io  0x0400-0x0453] has been reserved
[    0.372123] system 00:00: [io  0x0458-0x047f] has been reserved
[    0.372125] system 00:00: [io  0x0500-0x057f] has been reserved
[    0.372126] system 00:00: [io  0x164e-0x164f] has been reserved
[    0.372129] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.372152] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.372191] system 00:02: [io  0x0454-0x0457] has been reserved
[    0.372193] system 00:02: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    0.372405] pnp 00:03: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.372558] system 00:04: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.372559] system 00:04: [mem 0xfed10000-0xfed17fff] has been reserved
[    0.372560] system 00:04: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.372561] system 00:04: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.372562] system 00:04: [mem 0xf8000000-0xfbffffff] has been reserved
[    0.372563] system 00:04: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.372565] system 00:04: [mem 0xfed90000-0xfed93fff] could not be reserved
[    0.372566] system 00:04: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.372567] system 00:04: [mem 0xff000000-0xffffffff] could not be reserved
[    0.372568] system 00:04: [mem 0xfee00000-0xfeefffff] has been reserved
[    0.372570] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.372603] system 00:05: [mem 0x20000000-0x201fffff] has been reserved
[    0.372604] system 00:05: [mem 0x40000000-0x401fffff] has been reserved
[    0.372605] system 00:05: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.372685] pnp: PnP ACPI: found 6 devices
[    0.378686] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.378723] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.378740] pci 0000:00:1c.2: PCI bridge to [bus 02]
[    0.378742] pci 0000:00:1c.2:   bridge window [io  0x2000-0x2fff]
[    0.378749] pci 0000:00:1c.2:   bridge window [mem 0xe1000000-0xe19fffff]
[    0.378753] pci 0000:00:1c.2:   bridge window [mem 0xe0000000-0xe09fffff 64bit pref]
[    0.378761] pci 0000:00:1e.0: PCI bridge to [bus 03]
[    0.378771] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.378772] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.378773] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.378774] pci_bus 0000:00: resource 7 [mem 0xcfa00000-0xfeafffff window]
[    0.378775] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfed44fff window]
[    0.378776] pci_bus 0000:02: resource 0 [io  0x2000-0x2fff]
[    0.378777] pci_bus 0000:02: resource 1 [mem 0xe1000000-0xe19fffff]
[    0.378778] pci_bus 0000:02: resource 2 [mem 0xe0000000-0xe09fffff 64bit pref]
[    0.378779] pci_bus 0000:03: resource 4 [io  0x0000-0x0cf7 window]
[    0.378779] pci_bus 0000:03: resource 5 [io  0x0d00-0xffff window]
[    0.378780] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.378781] pci_bus 0000:03: resource 7 [mem 0xcfa00000-0xfeafffff window]
[    0.378782] pci_bus 0000:03: resource 8 [mem 0xfed40000-0xfed44fff window]
[    0.378859] NET: Registered protocol family 2
[    0.379025] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.379078] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.379143] TCP: Hash tables configured (established 32768 bind 32768)
[    0.379157] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.379169] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.379222] NET: Registered protocol family 1
[    0.379239] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.379559] PCI: CLS 64 bytes, default 64
[    0.379594] Unpacking initramfs...
[    0.675943] Freeing initrd memory: 21900K (ffff89d0f552a000 - ffff89d0f6a8d000)
[    0.675997] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.675999] software IO TLB [mem 0xc69fa000-0xca9fa000] (64MB) mapped at [ffff89d1869fa000-ffff89d18a9f9fff]
[    0.676413] audit: initializing netlink subsys (disabled)
[    0.676427] audit: type=2000 audit(1492096494.676:1): initialized
[    0.676667] Initialise system trusted keyrings
[    0.676757] workingset: timestamp_bits=40 max_order=20 bucket_order=0
[    0.676787] zbud: loaded
[    0.714937] Key type asymmetric registered
[    0.714938] Asymmetric key parser 'x509' registered
[    0.714953] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.714982] io scheduler noop registered
[    0.714983] io scheduler deadline registered
[    0.714995] io scheduler cfq registered (default)
[    0.715360] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.715364] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.715374] intel_idle: MWAIT substates: 0x1120
[    0.715375] intel_idle: v0.4.1 model 0x2A
[    0.715483] intel_idle: lapic_timer_reliable_states 0xffffffff
[    0.715637] GHES: HEST is not enabled!
[    0.715680] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.736174] 00:03: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    0.736602] Linux agpgart interface v0.103
[    0.736632] AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
[    0.736633] AMD IOMMUv2 functionality not available on this system
[    0.736938] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    0.739875] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.739878] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.740029] mousedev: PS/2 mouse device common for all mice
[    0.740061] rtc_cmos 00:01: RTC can wake from S4
[    0.740195] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[    0.740277] rtc_cmos 00:01: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
[    0.740286] intel_pstate: Intel P-state driver initializing
[    0.740469] ledtrig-cpu: registered to indicate activity on CPUs
[    0.741324] NET: Registered protocol family 10
[    0.741665] mip6: Mobile IPv6
[    0.741667] NET: Registered protocol family 17
[    0.741670] mpls_gso: MPLS GSO support
[    0.741938] microcode: sig=0x206a7, pf=0x2, revision=0x29
[    0.742043] microcode: Microcode Update Driver: v2.01 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    0.742251] registered taskstats version 1
[    0.742253] Loading compiled-in X.509 certificates
[    0.744536] alg: No test for pkcs1pad(rsa,sha256) (pkcs1pad(rsa-generic,sha256))
[    0.745009] Loaded X.509 cert 'Debian Project: Ben Hutchings: 008a018dca80932630'
[    0.745034] zswap: loaded using pool lzo/zbud
[    0.745449] rtc_cmos 00:01: setting system clock to 2017-04-13 15:14:55 UTC (1492096495)
[    0.745531] PM: Hibernation image not present or could not be loaded.
[    0.747470] Freeing unused kernel memory: 1396K (ffffffff90f2d000 - ffffffff9108a000)
[    0.747472] Write protecting the kernel read-only data: 12288k
[    0.748290] Freeing unused kernel memory: 2032K (ffff89d16b204000 - ffff89d16b400000)
[    0.752827] Freeing unused kernel memory: 1244K (ffff89d16b6c9000 - ffff89d16b800000)
[    0.762988] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    0.776919] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    0.777013] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    0.777025] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    0.777964] random: udevadm: uninitialized urandom read (16 bytes read)
[    0.778008] random: udevadm: uninitialized urandom read (16 bytes read)
[    0.779478] random: udevadm: uninitialized urandom read (16 bytes read)
[    0.779553] random: udevadm: uninitialized urandom read (16 bytes read)
[    0.779922] random: udevadm: uninitialized urandom read (16 bytes read)
[    0.779992] random: udevadm: uninitialized urandom read (16 bytes read)
[    0.780066] random: udevadm: uninitialized urandom read (16 bytes read)
[    0.807762] FUJITSU Extended Socket Network Device Driver - version 1.1 - Copyright (c) 2015 FUJITSU LIMITED
[    0.817998] pps_core: LinuxPPS API ver. 1 registered
[    0.817999] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.818767] PTP clock support registered
[    0.823894] ACPI: bus type USB registered
[    0.823923] usbcore: registered new interface driver usbfs
[    0.823934] usbcore: registered new interface driver hub
[    0.823957] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    0.823957] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    0.823959] usbcore: registered new device driver usb
[    0.824147] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[    0.825774] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.826326] ehci-pci: EHCI PCI platform driver
[    0.829199] SCSI subsystem initialized
[    0.834848] libata version 3.00 loaded.
[    0.846314] AVX version of gcm_enc/dec engaged.
[    0.846315] AES CTR mode by8 optimization enabled
[    0.971179] e1000e 0000:00:19.0 0000:00:19.0 (uninitialized): registered PHC clock
[    1.093030] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 18:03:73:dc:f6:7c
[    1.093032] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[    1.093069] e1000e 0000:00:19.0 eth0: MAC: 10, PHY: 11, PBA No: E041FF-0FF
[    1.093305] ehci-pci 0000:00:1a.0: EHCI Host Controller
[    1.093314] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[    1.093332] ehci-pci 0000:00:1a.0: debug port 2
[    1.094568] e1000e 0000:00:19.0 enp0s25: renamed from eth0
[    1.097237] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[    1.097420] ehci-pci 0000:00:1a.0: irq 16, io mem 0xe1a70000
[    1.111001] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[    1.111056] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.111057] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.111059] usb usb1: Product: EHCI Host Controller
[    1.111060] usb usb1: Manufacturer: Linux 4.9.0-0.bpo.2-amd64 ehci_hcd
[    1.111061] usb usb1: SerialNumber: 0000:00:1a.0
[    1.111307] hub 1-0:1.0: USB hub found
[    1.111316] hub 1-0:1.0: 2 ports detected
[    1.111591] ehci-pci 0000:00:1d.0: EHCI Host Controller
[    1.111596] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    1.111610] ehci-pci 0000:00:1d.0: debug port 2
[    1.115517] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[    1.115569] ehci-pci 0000:00:1d.0: irq 17, io mem 0xe1a50000
[    1.131007] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    1.131384] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.131387] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.131389] usb usb2: Product: EHCI Host Controller
[    1.131390] usb usb2: Manufacturer: Linux 4.9.0-0.bpo.2-amd64 ehci_hcd
[    1.131392] usb usb2: SerialNumber: 0000:00:1d.0
[    1.131725] hub 2-0:1.0: USB hub found
[    1.131769] hub 2-0:1.0: 2 ports detected
[    1.132153] ahci 0000:00:1f.2: version 3.0
[    1.132379] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3 impl SATA mode
[    1.132382] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems apst 
[    1.143805] scsi host0: ahci
[    1.144118] scsi host1: ahci
[    1.144346] scsi host2: ahci
[    1.144466] scsi host3: ahci
[    1.144561] scsi host4: ahci
[    1.144648] scsi host5: ahci
[    1.144703] ata1: SATA max UDMA/133 abar m2048@0xe1a40000 port 0xe1a40100 irq 27
[    1.144705] ata2: SATA max UDMA/133 abar m2048@0xe1a40000 port 0xe1a40180 irq 27
[    1.144706] ata3: DUMMY
[    1.144707] ata4: DUMMY
[    1.144708] ata5: DUMMY
[    1.144708] ata6: DUMMY
[    1.439012] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    1.458107] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.458131] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.458737] ata2.00: ATAPI: TSSTcorp DVD+/-RW SH-216AB, D200, max UDMA/100
[    1.458741] ata2.00: applying bridge limits
[    1.458982] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    1.459699] ata2.00: configured for UDMA/100
[    1.459859] ata1.00: ATA-8: WDC WD5000AAKX-753CA1, 19.01H19, max UDMA/133
[    1.459862] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.461852] ata1.00: configured for UDMA/133
[    1.462245] scsi 0:0:0:0: Direct-Access     ATA      WDC WD5000AAKX-7 1H19 PQ: 0 ANSI: 5
[    1.516426] scsi 1:0:0:0: CD-ROM            TSSTcorp DVD+-RW SH-216AB D200 PQ: 0 ANSI: 5
[    1.536611] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[    1.536680] sd 0:0:0:0: [sda] Write Protect is off
[    1.536683] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.536707] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.549462] sr 1:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.549472] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.549743] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.552467]  sda: sda1 sda2 < sda5 sda6 >
[    1.553323] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.591537] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[    1.591539] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.591790] hub 1-1:1.0: USB hub found
[    1.592279] hub 1-1:1.0: 6 ports detected
[    1.607561] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[    1.607564] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.607834] hub 2-1:1.0: USB hub found
[    1.608022] hub 2-1:1.0: 8 ports detected
[    1.691017] tsc: Refined TSC clocksource calibration: 3092.973 MHz
[    1.691024] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2c95594edb3, max_idle_ns: 440795220223 ns
[    1.800458] random: fast init done
[    1.903005] usb 2-1.6: new low-speed USB device number 3 using ehci-pci
[    1.904232] device-mapper: uevent: version 1.0.3
[    1.904367] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[    1.979000] raid6: sse2x1   gen()  5924 MB/s
[    2.047002] raid6: sse2x1   xor()  5939 MB/s
[    2.114998] raid6: sse2x2   gen() 11000 MB/s
[    2.182998] raid6: sse2x2   xor()  8169 MB/s
[    2.251006] raid6: sse2x4   gen() 13132 MB/s
[    2.319007] raid6: sse2x4   xor()  9947 MB/s
[    2.319008] raid6: using algorithm sse2x4 gen() 13132 MB/s
[    2.319008] raid6: .... xor() 9947 MB/s, rmw enabled
[    2.319009] raid6: using ssse3x2 recovery algorithm
[    2.320120] xor: automatically using best checksumming function   avx       
[    2.336305] Btrfs loaded, crc32c=crc32c-intel
[    2.391277] PM: Starting manual resume from disk
[    2.391281] PM: Hibernation image partition 8:5 present
[    2.391282] PM: Looking for hibernation image.
[    2.391556] PM: Image not found (code -22)
[    2.391558] PM: Hibernation image not present or could not be loaded.
[    2.424096] usb 2-1.6: New USB device found, idVendor=0603, idProduct=00f2
[    2.424098] usb 2-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.424100] usb 2-1.6: Product: USB Keyboard
[    2.424101] usb 2-1.6: Manufacturer: NOVATEK
[    2.429916] hidraw: raw HID events driver (C) Jiri Kosina
[    2.438544] usbcore: registered new interface driver usbhid
[    2.438545] usbhid: USB HID core driver
[    2.440561] input: NOVATEK USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.6/2-1.6:1.0/0003:0603:00F2.0001/input/input3
[    2.499445] hid-generic 0003:0603:00F2.0001: input,hidraw0: USB HID v1.10 Keyboard [NOVATEK USB Keyboard] on usb-0000:00:1d.0-1.6/input0
[    2.501103] input: NOVATEK USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.6/2-1.6:1.1/0003:0603:00F2.0002/input/input4
[    2.507031] usb 2-1.7: new low-speed USB device number 4 using ehci-pci
[    2.517274] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    2.559353] hid-generic 0003:0603:00F2.0002: input,hiddev0,hidraw1: USB HID v1.10 Device [NOVATEK USB Keyboard] on usb-0000:00:1d.0-1.6/input1
[    2.621406] usb 2-1.7: New USB device found, idVendor=046d, idProduct=c03e
[    2.621409] usb 2-1.7: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.621411] usb 2-1.7: Product: USB-PS/2 Optical Mouse
[    2.621413] usb 2-1.7: Manufacturer: Logitech
[    2.625598] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.7/2-1.7:1.0/0003:046D:C03E.0003/input/input5
[    2.625798] hid-generic 0003:046D:C03E.0003: input,hidraw2: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-1.7/input0
[    2.715223] clocksource: Switched to clocksource tsc
[    3.527093] systemd[1]: Failed to insert module 'kdbus': Function not implemented
[    3.658268] systemd[1]: systemd 230 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[    3.658454] systemd[1]: Detected architecture x86-64.
[    3.669726] systemd[1]: Set hostname to <LibraZiK-studio-audio>.
[    4.722519] systemd[1]: Reached target Remote File Systems (Pre).
[    4.722610] systemd[1]: Listening on fsck to fsckd communication Socket.
[    4.722733] systemd[1]: Created slice User and Session Slice.
[    4.722789] systemd[1]: Listening on Journal Socket.
[    4.722849] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    4.722885] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    4.722923] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    4.773495] random: crng init done
[    5.312495] lp: driver loaded but no devices found
[    5.410640] ppdev: user-space parallel port driver
[    5.432857] parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
[    5.567349] parport0: irq 7 detected
[    5.667415] lp0: using parport0 (polling).
[    5.718843] fuse init (API version 7.26)
[    7.723364] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[    7.795785] systemd-journald[707]: Received request to flush runtime journal from PID 1
[    7.999384] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input6
[    7.999388] ACPI: Power Button [PWRB]
[    7.999422] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input7
[    7.999423] ACPI: Power Button [PWRF]
[    8.042142] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[    8.053219] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    8.061928] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMIO) (20160831/utaddress-247)
[    8.061933] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    8.061935] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20160831/utaddress-247)
[    8.061938] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    8.061938] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20160831/utaddress-247)
[    8.061940] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    8.061940] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20160831/utaddress-247)
[    8.061942] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    8.061943] lpc_ich: Resource conflict(s) found affecting gpio_ich
[    8.197464] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    8.197506] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    8.256290] [drm] Initialized
[    8.292549] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters, 163840 ms ovfl timer
[    8.292551] RAPL PMU: hw unit of domain pp0-core 2^-16 Joules
[    8.292552] RAPL PMU: hw unit of domain package 2^-16 Joules
[    8.292552] RAPL PMU: hw unit of domain pp1-gpu 2^-16 Joules
[    8.299168] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[    8.415473] iTCO_vendor_support: vendor-support=0
[    8.662238] [drm] Memory usable by graphics device = 2048M
[    8.662240] [drm] Replacing VGA console driver
[    8.662763] Console: switching to colour dummy device 80x25
[    8.668888] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    8.668889] [drm] Driver supports precise vblank timestamp query.
[    8.671045] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[    8.671071] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
[    8.671182] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    8.671242] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[    8.686506] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[    8.686743] acpi device:01: registered as cooling_device4
[    8.686814] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input8
[    8.686885] [drm] Initialized i915 1.6.0 20160919 for 0000:00:02.0 on minor 0
[    8.701252] fbcon: inteldrmfb (fb0) is primary device
[    8.764604] Console: switching to colour frame buffer device 160x64
[    8.785589] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[    8.791462] snd_hda_codec_realtek hdaudioC0D0: ALC269VB: SKU not ready 0x411111f0
[    8.792002] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC269VB: line_outs=1 (0x1b/0x0/0x0/0x0/0x0) type:line
[    8.792004] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=1 (0x14/0x0/0x0/0x0/0x0)
[    8.792006] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[    8.792007] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[    8.792008] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[    8.792010] snd_hda_codec_realtek hdaudioC0D0:      Rear Mic=0x19
[    8.792012] snd_hda_codec_realtek hdaudioC0D0:      Front Mic=0x18
[    8.824181] snd_hda_intel 0000:00:1b.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[    8.826096] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[    8.827216] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[    8.827293] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[    8.827396] input: HDA Intel PCH Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[    8.828637] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[    8.828706] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
[    9.097539] intel_rapl: Found RAPL domain package
[    9.097541] intel_rapl: Found RAPL domain core
[    9.097543] intel_rapl: Found RAPL domain uncore
[    9.097549] intel_rapl: RAPL package 0 domain package locked by BIOS
[   10.284376] Adding 4071420k swap on /dev/sda5.  Priority:-1 extents:1 across:4071420k FS
[   18.389801] e1000e: enp0s25 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[  675.037133] usb 1-1.4: new high-speed USB device number 3 using ehci-pci
[  675.284696] usb 1-1.4: New USB device found, idVendor=06f8, idProduct=e010
[  675.284699] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  675.284701] usb 1-1.4: Product: 802.11 bg WLAN
[  675.284702] usb 1-1.4: Manufacturer: Ralink
[  675.493204] usb 1-1.4: reset high-speed USB device number 3 using ehci-pci
[  675.932023] ieee80211 phy0: rt2x00_set_chip: Info - Chipset detected - rt: 2573, rf: 0002, rev: 000a
[  675.945285] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[  675.946106] usbcore: registered new interface driver rt73usb
[  676.022565] rt73usb 1-1.4:1.0 wlx0008d3359008: renamed from wlan0
[  676.069218] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt73.bin'
[  676.086441] rt73usb 1-1.4:1.0: firmware: direct-loading firmware rt73.bin
[  676.086446] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 1.7
[  677.601295] wlx0008d3359008: authenticate with 14:0c:76:f8:6d:28
[  677.649291] wlx0008d3359008: send auth to 14:0c:76:f8:6d:28 (try 1/3)
[  677.651054] wlx0008d3359008: authenticated
[  677.653242] wlx0008d3359008: associate with 14:0c:76:f8:6d:28 (try 1/3)
[  677.659058] wlx0008d3359008: RX AssocResp from 14:0c:76:f8:6d:28 (capab=0x411 status=0 aid=2)
[  677.669946] wlx0008d3359008: associated
root@LibraZiK-studio-audio:/home/nicolasmao2#


tenryu utilisateur non connecté France
Donc , ça n'est pas le microcode. Et ton ifconfig te dis que l'interface marche ( puisque les paquets sont reçus et transmis sans erreur). Là, je sèche !

calixtus06 utilisateur non connecté
Pas d'idée ? j'ai vérifié que la clef n'était pas endommagée mais elle scanne bien. Un truc que je me dis c'est que j'ai appellé cet ordi nicolasmao2 alors que mon ancien s'appelle nicolasmao. Cela pourrait il poser un problème ?

Image

olinuxx utilisateur non connecté France
calixtus06 écrit :
Quoi comprendre ?


Que tu dois désactiver (en la décochant) la ligne qui te parle d'un CD debian, et mettre le "non-free" dans la ligne indiquée dans l'image ci dessous :
Image


calixtus06 écrit :
On me redemande de choisir la box , de réinscrire la clef de sécurité et là ça cherche pendant des plombes sans valider la connection ( ???) .

" obtention d'une adresse réseau wi-fi pour "freebox_nicolas_ni"....


C'est qui ce "on" qui te demande des trucs ? :-)
Fait des captures d'écran en expliquant précisément ce que tu fais, où est-ce que tu cliques, ...

calixtus06 utilisateur non connecté
( je ne suis pas à la maison et te réponds partiellement)

Le "on" c'est l'encart où sont visibles le noms des box alentour à l'ordi ( neuf box de bidule, freebox de machin etc ) quand je fais un clic gauche sur l'icône en haut à gauche

Image

ensuite je clique sur ma box et rentre la clef de sécurité.

A l'endroit de l'icône de wifi j'ai ensuite un dessin qui tourne sans arrêt signifiant je pense une obtention d'adresse ip puisque quand je passe la souris sur cet icône il y a un message en noir me disant un truc du genre attente d'obtention d'adresse ip.

Remarque de novice: quand j'ai fais l'installation de librazik sur ce nouvel ordi, il y avait une connection internet via la clef usb wifi.

Une fois la machine nommée, c'est là que ça a foiré ( plus de connection) . Or effectivement les deux noms de machines ( le premier ordi où j'ai mis librazik et ce nouvel ordi ) sont proches nicolasmao et nicolasmao2.

Estr ce que ça peut nenir de là ?

calixtus06 utilisateur non connecté
olinuxx écrit :
Que tu dois désactiver (en la décochant) la ligne qui te parle d'un CD debian, et mettre le "non-free" dans la ligne indiquée dans l'image ci dessous :


Image

c'est bon comme ça ?

sub26nico utilisateur non connecté France
oui ça m'a l'air bon.
J'en profiterais aussi pour éliminer les doublons:
tu as 2 fois les dépôts USERS de LibraZiK :
à chaque fois une ligne "deb" et une "deb-src".
Tu peux décocher les 2 derniers, ça ne changera pas grand chose
hormis le message d'erreur que tu dois avoir à chaque fois
que tu recharge Synaptic ou que tu fais des mises à jour.

calixtus06 utilisateur non connecté
sub26nico écrit :
hormis le message d'erreur que tu dois avoir à chaque fois
que tu recharge Synaptic ou que tu fais des mises à jour.


Il se tard et je ne comprends plus grand chose mais pourquoi ces messages d'erreur quand je fais les mises à jour ?

sub26nico utilisateur non connecté France
Tout est expliqué ici .

olinuxx utilisateur non connecté France
calixtus06 écrit :
Une fois la machine nommée, c'est là que ça a foiré ( plus de connection) . Or effectivement les deux noms de machines ( le premier ordi où j'ai mis librazik et ce nouvel ordi ) sont proches nicolasmao et nicolasmao2.

Estr ce que ça peut nenir de là ?


Non, je ne pense pas.

Autre possible source d'erreur : le mot de passe. Es-tu sûr et certain que tu tapes le mot de passe correctement ? Spécialement les différences entre majuscules et minuscules, les caractères spéciaux, ... il me semble (de mémoire), qu'il est possible de faire apparaître les caractères que tu tapes.

calixtus06 utilisateur non connecté
olinuxx écrit :
Autre possible source d'erreur : le mot de passe. Es-tu sûr et certain que tu tapes le mot de passe correctement ? Spécialement les différences entre majuscules et minuscules, les caractère spéciaux, ... il me semble (de mémoire), qu'il est possible de faire apparaître les caractères que tu tapes.


Oui justement je le fais toujours apparaître au cas où.

J'ai tenté de déconnecter puis reconnecter et là la connection se fait automatiquement sans que j'ai la possibilité de rentrer à nouveau la clef de sécurité (??)

Avec ifconfig, à la place de wlan0 c'est un truc bizarre:

wlx0008d3359008 Link encap:Ethernet  HWaddr 00:08:d3:35:90:08  
          adr inet6: fe80::208:d3ff:fe35:9008/64 Scope:Lien
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:18 errors:0 dropped:0 overruns:0 frame:0
          TX packets:30 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:1000 
          RX bytes:5348 (5.2 KiB)  TX bytes:6199 (6.0 KiB)


Autre dernière bizarrerie : sur l'icône de connection il y a noté "réseau wifi: micrologiciel manquant"

olinuxx utilisateur non connecté France
calixtus06 écrit :
Autre dernière bizarrerie : sur l'icône de connection il y a noté "réseau wifi: micrologiciel manquant"


Plutôt explicite comme message qui te dit qu'il manque le micrologiciel ("firmware" en anglais) pour la puce wifi de la machine. Installe le paquet correspondant a ton interface wifi de la liste https://github.com/LibraZiK/LibraZiK-live/tree/master/amd64%2Bfirmwares/config/packages.binary . Tu devras activer la catégorie "non-free" du dépôt debian comme expliqué ici .

Page : 1/3  [Suivant]
1  2  3 
Afficher les articles :
Aller au forum :

Documentation [Afficher / Cacher]

Connexion
[Afficher / Cacher]


autumn

Mégaphone [Afficher / Cacher]

programLyrique, 16:04, ven. 15 Dec 2017: organteq, une modélisation physique gratuite d'orgue par pianoteq [Lien]
sub26nico, 12:22, ven. 15 Dec 2017: Salut et bienvenue à courgain et Genegilor :-)
olinuxx, 17:38, jeu. 14 Dec 2017: Bonjour et bienvenue à autumn :-)
sub26nico, 14:58, jeu. 14 Dec 2017: Salut et bienvenue à idens :-)
olinuxx, 19:39, mer. 13 Dec 2017: Bonjour et bienvenue à LeZaz et ggz :-)
olinuxx, 15:00, mer. 13 Dec 2017: @Eternal_happ : l'adresse courriel que tu as utilisée pour ton inscription est invalide. Contacte moi à l'adresse info AROBAZE linuxmao POINGT org
olinuxx, 14:15, mer. 13 Dec 2017: Bonjour et bienvenue à Jazus :-)
olinuxx, 23:47, mar. 12 Dec 2017: @zebassprophet : ouh yeah cool
zebassprophet, 22:47, mar. 12 Dec 2017: y'a un librazik 2 alors? s'en passe des trucs pendant que je deprime dans mon coin ^^
olinuxx, 22:41, mar. 12 Dec 2017: Bonjour et bienvenue à Eternal_happ :-)
Paulart, 16:28, mar. 12 Dec 2017: Hey !!! Besoin de connaisseurs sur Paris les amis ! [Lien]
sub26nico, 15:34, mar. 12 Dec 2017: Salut et bienvenue à sylk et strium :-)